Видео

Great video, where can i find that rachet?

So nobody else noticed the tornado siren in the background lmao

why not cut the old one first?

Thanks, for the great video!! It is surprising how few videos there are on the 2003 Exmark Lazer Z. I have the 26HP EFI Kohler. I wanted to get parts from the Kohler engines or Exmark website but my mower was completely edited from all the listings. Probably because the company was sold years after my mower was built. I don’t know. But this video was very helpful. Thanks again

Dude you saved the day!!!! We were looking for a larger bearing puller and could not find one, you saved us from having to cut the thing off. Worked amazingly well!!!!

Sir it is ok to use in TOYOTA YARIS HYBRID 2018 model? I want to make sure . Thanks in advance.

Big help man! Thanks. 👍

I have three dead outlets and all the breakers are on.

Don't have a press have to reset gears after bad install. Learning as I go. Thanks.

Dude - there is NO difference in the tones. And, if there is and you can’t hear it in the video - what’s the point of the video? Useless

Looks like if you shim that base up a bit it wouldn't wobble so much and be more solid. Maybe a large washer.

so many goofs. ALWAYS wipe and clean the rim before and after. Also do not apply petroleum based chemical to rubber. Simple dish soap is perfect, water soluble, non toxic. Apply to all surfaces including tools. Hold the camara still. Use a pair of vice grips, use thinner, smaller tools. Huge tools will: deform the rim, tear the soft rubber

Here is a variation of thread repair kits amzn.to/3ydeHdd Definitely check it out

getting this for prime day, just wanted to see if how and if it works

Ok so I am sure gunna be dumb question. But what exactly is that rubber nipple cover that you show in the video that is to the right of kickstand and right next to the lift section? I have seen others put the one point of lift directly on that as if it is ment to use as a jack point?? Any help??

Just bought mine. I have the same click, because the car had been sitting too long.

Thank you 👍🏻

Thank you

Don't do this! That will not last long. Vacuum out system, cut line, solder ac fitting and refill.

What size nut dose that bolt take?

Surprised this is the first video that popped up when searching. Amateur hour.

Now show us how it is done without destroying the bearing using a proper pinion puller.

What about the adapter?

LOL

What if you don't have those things. Dang gone it

Before the compressor or after the compressor? Unclear of which it is?

What size ?

I am looking at TWO stators out of a 12 hp ride on.....the copper wiring on the stator that is wrapped around every post is SCREWED to the metal ring??? How can it not touch when they screwed it to the metal??? Something wrong here....

man those 15"- tires are a pain in the butt!

This has to be my least favourite job with wrenching on older cars. Not fun when it all goes south!

How do you know what pipe to pierce

Thank you

I over filled my 1990 bronco 2 by a quart! I don't want to drain the pan yet. I wonder if you can get the pump and tubing at Harbor Freight ? Thanks for the video I'll do it!

i wish mine would click off like that but man these extractor sockets aren't doin the job lol

It’s a solution, but not a great one in my opinion. You would have to pull your seat every time to get the Velcro loose. You know why Harley put those stupid clips on there to begin with don’t you? Lol. Good ole Harley. You have to buy it. Then you have to build it.

Very helpful. The only thing I would add to your video would be what to do with the transmission fluid that you removed.

I never had any luck with the extractor. I had to use a nut splitter.

Spend all that money on a Harley and have to use Velcro to hold the bike together, seems like someone would have made a new design by now

my man, i just picked up a similar kit at McFaddendale's here in Vegas...i was informed we need to pop that tang end off before it's complete... not really?

Great video! I just bought a 2003 Sportster XL1200S and needed to know how to jack it up. Your video was exactly was I was looking for. Thank you!

Thanks

Thaks Handyman. Your video was right on. Its guys like you that make RUclips Great!!!

What was the part number of that belt?

I never got through the entire video because the soundtrack made me kill myself.

Hey buddy Tks for the common sense video. I would’ve had a harder time if not for this. ☮️

Hey handyman. You still happy w APlus Lift? Im building a shop right now with 12x12 doors and 14 ft high ceilings. I feel like buying the API certified APlus Lift. Can i go wrong by doing so? I have 6.0-6.5" thick, 6SACK cement floor with 3/4" imbedded fibers and rebar.

You needs to put on gloves on for safety purposes

Thank you for sharing this! Game changer.

The scratch will do no harm 😂 🤦🏻

10 years later, I'm here to learn 🎉